-
product
High-Speed Embedded Host Electrical Test Board
HSEHET
High-Speed Embedded Host Electrical Test Board is approved by USB-IF, specifically designed for the electrical test of USB embedded host products.
-
product
Test Fixturing
There are no good measurements without good test fixtures. Ideally the test fixture needs to make the electrical connection between the test instrument and the device-under-test (DUT) and be electrically transparent. ATE has developed fixtures for SMT components, leadless packages, and miniature coaxial interfaces, in such a way that the fixture effects can be removed, and the measurement reference plane can be brought right down to the DUT.
-
product
Airproof Test Bench For Complete Gas Meter
Bofa Instrument & Equipment Co., Ltd
Airproof test bench for complete gas meter is a device to test a complete gas meter airproof. The bench is adopting compare method by comparing tested meters with a standard tank. It is suitable for gas meter with steel case or aluminum case.
-
product
Primary Test Equipment
LET-400
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
-
product
Low Noise Test Cables For N1413 With B2980 Series, 3m
N1427B
The N1427B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1427B to the B2985B/87B.
-
product
Secondary Injection Test Set
PTE-100-C Plus
In the Pro version this voltage source incorporates a dedicated LCD display and its own BUS-PTE connection that make the operation easier and enable it to be used also with other sets in the PTE range.
-
product
Becker NAV/RMU/RMI/OBS Test Fixture
TA-3320
This NAV test fixture is specific to the requirements for testing Becker Avionics NAV, RMI and RMU products. The panel incorporates specific functionality required for testing these Becker products by the book including special requirements for the RMU 5000 and the IN 3300 series of nav indicators. This BAEE NAV test fixture also facilitates resolver alignment and discrete meter testing through the PG 3300 interface connector. The RM 3300 portion of the panel tests the Becker RMI indicators and ...show more -
product
Semiconductor Test Services
Tests regarding function, electrical and optoelectronical parameter. Electrical test of wafer up to 8? and packaged devices - selection and volume test.
-
product
FLUKE® Test Tools
Testwave LLC® has been selling, renting, calibrating and servicing Fluke Products for over seventeen years.
-
product
ARINC 429 Test And Simulation PCIe Module
PCIe-C429
*4, 8, 16 or 32 software programmable TX / RX channels*X4 lane PCI Express host interface*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
Pneumatic Vertical Shock Response Spectrum Test System
KRD14 series
KRD14 series pneumatic shock response spectrum tester is used to measure and determine the shock resistance of electrical and electronic products or packaging, and to evaluate the reliability and structural integrity of the test product in a shock environment. The shock response spectrum is the total result of a series of single-degree-of-freedom linear systems with different natural frequencies subjected to the same shock excitation response. When a product is subjected to an impact, the maximu...show more -
product
Modbus Test & Simulation Software
ModBus Constructor 1.7
Using Modbus Constructor you can quickly create a data management model for any of your Modbus devices. Unlike other available solutions on the market which provide displaying data as columns of abstract numbers of the same type, Modbus Constructor represents each data element exactly as you need. You may define type, format or scale independently. This makes them easy to read and analyze.
-
product
Four Position Meter Test Bench
TB41
Calmet Smart Calibration Devices
The Calmet TB41 Four Position Meter Test Bench is used for calibration and simultaneously testing up to four single and three phase electromechanical and electronic acitve and reactive electricity meters with accuracy referenced to an internal reference meter (class 0.02% or 0.04%).
-
product
Diagnostic Relay Buddy 12/24 Test Kit
193
Relay Buddy 12/24 Pro Test Kit tests five different relays. Relay Buddy is a quick go / no-go tester for the most common automotive relays and this new version tests both 12 and 24 volt relays. . If the relay fails the test, 3 different trouble codes will advise you of the possible causes for the failed relay. The red LED will flash once, twice or three times to indicate the problem. Trouble code definitions are printed on the back of the tester for your convenience.
-
product
V4 Marine Communications System - V4 NAVTEX Test System
The ICS Electronics Limited V4 NAVTEX Test system may be used for type approval, general performance testing and production testing of NAVTEX receivers.
-
product
Speaker Test
Determines speaker polarity by analyzing a proprietary signal. See our new demo video of this module. Measures woofers, midrange, and tweeter drivers.
-
product
Tan Delta Test Set
TD 5000
The high-voltage generator TD 5000 is a complementary module of STS serie. TD 5000 designed to perform Tan Delta measurements, dissipation factor and capacitance of transformer and bushing at the frequency of the mains or in a wide frequency range.
-
product
Rack Mountable Video Test Generator
804B
The Teledyne LeCroy rack mountable quantumdata 804B video test generator is optimized for testing modern HDMI flat panel TVs. The 804B video test generator supports testing of HDMI resolutions operating up to 600 MHz. This enables testing ultra HD TVs with 4K resolutions at 50/60Hz using HDMI 2.0 4:4:4 pixel encoding. The 804B supports analog component YPbPr pixel rates up to 75 MHz and RGB analog outputs at pixel rates up to 162 MHz.
-
product
Test Instrument for LAN Cabling Verification
MI 2016 Multi LAN 350
High performance, multifunction test instrument for LAN cabling verification.
-
product
Adhesion test with disposable 2.25" disc
ADHOR400
The Adhor portable tester is ideal for your quality test on coating layer. It allows you to evaluate easily on the field the pull strength (commonly called adhesion) of your coating system on various substrates.
-
product
Test Connectors
The need for contacting standard USB or RJ connections and interfaces is increasing in the field of in-circuit and functional tests of PCBs because the standardization of these interfaces has great advantages.
-
product
Rapid Temperature Change Test Chamber
Wewon Environmental Chambers Co, Ltd.
The Wewon’s rapid temperature change test chamber is equipped with two 1.5 kW French Tecumseh compressors, Cooling capacity temperature change rate can be 3℃ / min. The machine can carry out on-line product quality inspection task according to the specified temperature change rate. The volume and wind speed will be adjusted automatically, This makes the temperature in the test area is evenly distributed. Through an electronic expansion valve, The surface temperature difference of the tested product is suppressed, and the linear control precision is realized.https://www.wewontech.com/rapid-temperature-change-test-chamber/
-
product
Advanced Burn-in and Test System for packaged parts
ABTS-Li
High power logic individual temperature control
-
product
SCT IFCC Self Test Box
MS 3647I
SCT-IFCC Self-Test Box is standard portable 19” rack mountable unit. It is customized unit for single channel tester of IFCC. This unit has testing facility of all Inputs and outputs of Single channel tester of IFCC.
-
product
Special Application Products
Special applications from APPA. Browse our special applications from voltage testers to thermometers and other products.
-
product
Current And Voltage Transformer Test Set
iCT1
iCT1 - CT/VT Test Set is the NEW and most advanced portable equipment capable to test current, voltage and combined transformers.With the low voltage method, known as "DC method", iCT1 is able to test Current Transformers with a very high saturation voltage, up to 30 kV, in a complete safety mode. Quick and easy to use tool, iCT1 allows to perform tests in one shot without changing the connection to the CT, thanks to the integrated 5-TAP Switchbox.
-
product
SPD High, Medium, and Low Voltage TOV Test Equipment
Shanghai Guantu Technology Co., Ltd.
The high (medium) voltage TOV tester is used for transient overvoltage tests caused by faults in high and medium voltage systems such as surge protectors (SPDs), and can also be used for other scientific research tests.standardGB/T 16927-1997 High voltage test technology.GB18802.1-2011 Surge protective device (SPD) for low-voltage power distribution system Part: Performance requirements and test methods.IEC61643-1:2005 (Surge protective devices connected to low-voltage power distribution systems...show more -
product
RF/Microwave Test Capability
Teledyne Labtech have extensive microwave alignment and microwave testing facilities. This includes the ability to test noise figure, S-parameters and harmonics. This ensures that Teledyne Labtech can supply a fully compliant product and provide a complete turnkey microwave assembly and test solution.
-
product
IEC60884-1 Low Temperature Thermal Shock Test Device
CX-DWC
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884-1 Uses: It is used to evaluate the impact resistance of electrical accessories under low temperature conditions, and also to evaluate the low temperature impact resistance of wire and cable.
-
product
Relays for High Power Applications
Series ST
Series ST relays are designed for high-power applications. The design incorporates an SCR or triac output. The relays utilize optical isolation to protect the control from load transients. A control LED is available on certain models. Internal MOV is also available on ST24D 25A and 50A models. All Series ST relays are Zero-Cross switching.Available options include:ST24D12 12A, 12-280Vrms, 600Vpeak Load; 4-30Vdc ControlST24D25 25A, 12-280Vrms, 600Vpeak Load; 4-30Vdc ControlST48D50 50A, 24-600Vrms, 1200Vpeak Load; 5-30Vdc Control